USER MANUAL

WAD Console Tablet

 

 

TABLE OF CONTENTS

1. Introduction

Each WAD-110 and 120 unit comes with a console tablet instead of a monitor, keyboard and mouse. The console tablet has the advantages of simplicity and mobility for the venue managers. The console tablet is an optiona device for WAD-104. For inquiry, please contact sales@cinet.com or 1-747-220-0120.

Specifications

  • 8 inch Touch Screen Display
  • Android 4.1 Ice Cream Sandwich
  • 1024 x 768 Resolution
  • Dual Core 1.6 Ghz
  • WiFi 802.1 b/g/n
  •  

    2. Console for WAD-110

    2.1 How to use the Console Tablet

    Power on the console tablet. Depending on what model of your tablet, power button may be located on either top or to the side. Please refer to user manual of the tablet for more information.

    From the homepage, go to the Settings > WiFi to connect to the router. This is the router which is configured to the WAD-110. For the presentation, we name the router as CiNet.com 5G.

    Return to the homepage and press the console app "CiNet.com" icon to start the console program. Go to the SYSTEM page, if different at the start.

    You will see the blank fields for the Server name and Channel names 1 - 4. Input the Server name and press Apply button on the right side. The message "Updated server information successfully" will appear indicating the Server name has been updated as shown below.

    For the channel names, there are two ways to input them.

    First, if the channel is from a Direct TV satellite box, you can choose to input the IP address of the channel in the DIRECT TV page and let the names of the channel and program automatically fill in. This service requires the DECA Broadbank connector as shown in Section 1.5 above. As for the IP address, it can be found in the TV by going to Menu > Settings & Help > Settings > Network Setup > Network Services. There the IP address will be displayed. Sometimes the IP addess shown can be wrong or incorrect. To correct the false IP address, go to Menu > Settings & Help > Settings > Network Setup > Restore Defaults. After the restoring the default, repeat the step above to find the IP address and input it into the Direct TV page fo the console App.

    Here we inputted the IP addresses for 3 channels coming from the Direct TV. After inputting the IP address, press Apply and wait for the confirmation.

    Second, if the channel is not coming from the Direct TV, you can manually input the name of the channel in the SYSTEM page. We inputted the name "local" for the 4th channel. Note that for the channels 1-3, the names of the channel and program have already filled in automatically from the Direct TV. These names will also appear on the MONITOR page as well as on each of the smartphones and tablets listening to the channels

    Next we go to the MONITOR page. Here you can monitor the volume level of each channel and also the number of logins listening to each channel. Note that the name of the channel and program for each channel are displayed.

    As shown by the volume level, the channel 4 is not turned on. Also shown below in the MONITOR page are the server name, the router name, speed of the transmission, and the signal strength.

    There is the REBOOT button on the SYSTEM and DIRECT TV page. When troubleshooting the system, press the REBOOT button to restart the WAD-110.

    There is the POWER OFF button on the DIRECT TV page. Press to shut down the WAD-110.


    2.2 How to change the Stereo / Mono mode in WAD-110

    Go to the SYSTEM page in the console program. You will see the STEREO button on the right side. Press the button and it will change to MONO with a light lit. You will also see the channel number increasing to 8.

    If there are existing IP addresses inputted in the DIRECT TV page for the STEREO mode, upon chaning to the MONO, the addresses will duplicate into the both right and left sides, now separated as indepedent channels. Below is the picture of a possible outcome from chaning of the STEREO mode to the MONO mode. Of course, if there are no IP addresses inputted before, the channel name fields will come up empty.

    In the DIRECT TV page, you will also see the change.

    Input the IP addresses as you wish.

    Chaning from the MONO to the STEREO is exactly the opposite. Go to the SYSTEM page and press the MONO button. It will change to STEREO with the light turn off.

     

    2.3 How to input the Direct TV IP addresses for Auto Channel Naming

    If the audio channel is connected a Direct TV satellite box, you can input the IP address of the channel in the DIRECT TV page and let the names of the channel and program automatically fill in. This service requires the DECA Broadbank connector as shown in Section 1.5 above. As for the IP address, it can be found in the TV by going to Menu > Settings & Help > Settings > Network Setup > Network Services. There the IP address will be displayed. Sometimes the IP addess shown can be wrong or incorrect. To correct the false IP address, go to Menu > Settings & Help > Settings > Network Setup > Restore Defaults. After the restoring the default, repeat the step above to find the IP address and input it into the Direct TV page fo the console App.

    Input the IP addresses in the DIRECT TV page and press the Apply button. The message "Updated server information successfully" will appear to confirm your input.

    For the picture above, we inputted IP addresses for 3 channels. Next go to the SYSTEM page and wait 3 seconds for the names of the channels and programs to appear automatically.



    3. Console for WAD-120

    3.1 How to use the Console Tablet

    Power on the console tablet. Depending on what model of your tablet, power button may be located on either top or to the side. Please refer to user manual of the tablet for more information.

    From the homepage, go to the Settings > WiFi to connect to the router. This is the router which is configured to the WAD-110. For the presentation, we name the router as CiNet.com 5G.

    Return to the homepage and press the console app "CiNet.com" icon to start the console program. Go to the SYSTEM page, if different at the start.

    You will see the blank fields for the Server name and Channel names 1 - 4. Input the Server name and press Apply button on the right side. The message "Updated server information successfully" will appear indicating the Server name has been updated as shown below.

    For the channel names, there are two ways to input them.

    First, if the channel is from a Direct TV satellite box, you can choose to input the IP address of the channel in the DIRECT TV page and let the names of the channel and program automatically fill in. This service requires the DECA Broadbank connector as shown in Section 1.5 above. As for the IP address, it can be found in the TV by going to Menu > Settings & Help > Settings > Network Setup > Network Services. There the IP address will be displayed. Sometimes the IP addess shown can be wrong or incorrect. To correct the false IP address, go to Menu > Settings & Help > Settings > Network Setup > Restore Defaults. After the restoring the default, repeat the step above to find the IP address and input it into the Direct TV page fo the console App.

    Here we inputted the IP addresses for 3 channels coming from the Direct TV. After inputting the IP address, press Apply and wait for the confirmation.

    Second, if the channel is not coming from the Direct TV, you can manually input the name of the channel in the SYSTEM page. We inputted the name "local" for the 4th channel. Note that for the channels 1-3, the names of the channel and program have already filled in automatically from the Direct TV. These names will also appear on the MONITOR page as well as on each of the smartphones and tablets listening to the channels

    Next we go to the MONITOR page. Here you can monitor the volume level of each channel and also the number of logins listening to each channel. Note that the name of the channel and program for each channel are displayed.

    As shown by the volume level, the channel 4 is not turned on. Also shown below in the MONITOR page are the server name, the router name, speed of the transmission, and the signal strength.

    There is the REBOOT button on the SYSTEM and DIRECT TV page. When troubleshooting the system, press the REBOOT button to restart the WAD-120.

    There is the POWER OFF button on the DIRECT TV page. Press to shut down the WAD-120.


    3.2 How to change the Stereo / Mono mode in WAD-120

    Go to the SYSTEM page in the console program. You will see the STEREO button on the right side. Press the button and it will change to MONO with a light lit. You will also see the channel number increasing to 8.

    If there are existing IP addresses inputted in the DIRECT TV page for the STEREO mode, upon chaning to the MONO, the addresses will duplicate into the both right and left sides, now separated as indepedent channels. Below is the picture of a possible outcome from chaning of the STEREO mode to the MONO mode. Of course, if there are no IP addresses inputted before, the channel name fields will come up empty.

    In the DIRECT TV page, you will also see the change.

    Input the IP addresses as you wish.

    Chaning from the MONO to the STEREO is exactly the opposite. Go to the SYSTEM page and press the MONO button. It will change to STEREO with the light turn off.

     

    3.3 How to input the Direct TV IP addresses for Auto Channel Naming

    If the audio channel is connected a Direct TV satellite box, you can input the IP address of the channel in the DIRECT TV page and let the names of the channel and program automatically fill in. This service requires the DECA Broadbank connector as shown in Section 1.5 above. As for the IP address, it can be found in the TV by going to Menu > Settings & Help > Settings > Network Setup > Network Services. There the IP address will be displayed. Sometimes the IP addess shown can be wrong or incorrect. To correct the false IP address, go to Menu > Settings & Help > Settings > Network Setup > Restore Defaults. After the restoring the default, repeat the step above to find the IP address and input it into the Direct TV page fo the console App.

    Input the IP addresses in the DIRECT TV page and press the Apply button. The message "Updated server information successfully" will appear to confirm your input.

    For the picture above, we inputted IP addresses for 3 channels. Next go to the SYSTEM page and wait 3 seconds for the names of the channels and programs to appear automatically.


    4. Console for WAD-104

    4.1 How to use the Console Tablet

    Power on the console tablet. Depending on what model of your tablet, power button may be located on either top or to the side. Please refer to user manual of the tablet for more information.

    From the homepage, go to the Settings > WiFi to connect to the router. This is the router which is configured to the WAD-104. For the presentation, we name the router as CiNet.com 5G.

    Return to the homepage and press the console app "CiNet.com" icon to start the console program. Go to the SYSTEM page, if different at the start.

    You will see the blank fields for the Server name and Channel names 1 - 4. Input the Server name and press Apply button on the right side. The message "Updated server information successfully" will appear indicating the Server name has been updated as shown below.

    For the channel names, there are two ways to input them.

    First, if the channel is from a Direct TV satellite box, you can choose to input the IP address of the channel in the DIRECT TV page and let the names of the channel and program automatically fill in. This service requires the DECA Broadbank connector as shown in Section 1.5 above. As for the IP address, it can be found in the TV by going to Menu > Settings & Help > Settings > Network Setup > Network Services. There the IP address will be displayed. Sometimes the IP addess shown can be wrong or incorrect. To correct the false IP address, go to Menu > Settings & Help > Settings > Network Setup > Restore Defaults. After the restoring the default, repeat the step above to find the IP address and input it into the Direct TV page fo the console App.

    Here we inputted the IP addresses for 3 channels coming from the Direct TV. After inputting the IP address, press Apply and wait for the confirmation.

    Second, if the channel is not coming from the Direct TV, you can manually input the name of the channel in the SYSTEM page. We inputted the name "local" for the 4th channel. Note that for the channels 1-3, the names of the channel and program have already filled in automatically from the Direct TV. These names will also appear on the MONITOR page as well as on each of the smartphones and tablets listening to the channels

    Next we go to the MONITOR page. Here you can monitor the volume level of each channel and also the number of logins listening to each channel. Note that the name of the channel and program for each channel are displayed.

    As shown by the volume level, the channel 4 is not turned on. Also shown below in the MONITOR page are the server name, the router name, speed of the transmission, and the signal strength.

    There is the REBOOT button on the SYSTEM and DIRECT TV page. When troubleshooting the system, press the REBOOT button to restart the WAD-104.

    There is the POWER OFF button on the DIRECT TV page. Press to shut down the WAD-104.


    4.2 How to change the Stereo / Mono mode in WAD-104

    Go to the SYSTEM page in the console program. You will see the STEREO button on the right side. Press the button and it will change to MONO with a light lit. You will also see the channel number increasing to 8.

    If there are existing IP addresses inputted in the DIRECT TV page for the STEREO mode, upon chaning to the MONO, the addresses will duplicate into the both right and left sides, now separated as indepedent channels. Below is the picture of a possible outcome from chaning of the STEREO mode to the MONO mode. Of course, if there are no IP addresses inputted before, the channel name fields will come up empty.

    In the DIRECT TV page, you will also see the change.

    Input the IP addresses as you wish.

    Chaning from the MONO to the STEREO is exactly the opposite. Go to the SYSTEM page and press the MONO button. It will change to STEREO with the light turn off.

     

    4.3 How to input the Direct TV IP addresses for Auto Channel Naming

    If the audio channel is connected a Direct TV satellite box, you can input the IP address of the channel in the DIRECT TV page and let the names of the channel and program automatically fill in. This service requires the DECA Broadbank connector as shown in Section 1.5 above. As for the IP address, it can be found in the TV by going to Menu > Settings & Help > Settings > Network Setup > Network Services. There the IP address will be displayed. Sometimes the IP addess shown can be wrong or incorrect. To correct the false IP address, go to Menu > Settings & Help > Settings > Network Setup > Restore Defaults. After the restoring the default, repeat the step above to find the IP address and input it into the Direct TV page fo the console App.

    Input the IP addresses in the DIRECT TV page and press the Apply button. The message "Updated server information successfully" will appear to confirm your input.

    For the picture above, we inputted IP addresses for 3 channels. Next go to the SYSTEM page and wait 3 seconds for the names of the channels and programs to appear automatically.

    END